Asphalt Tonnage Calculator for Paving
Estimate US short tons of asphalt from paved area, finished thickness in inches, and the supplier’s compacted density in pounds per cubic foot.
Estimate concrete in cubic yards, flooring in boxes, lumber in board feet and roofing area from pitch. Use the dimensions and units listed for each project.
Try a shorter search or choose another category.
Estimate US short tons of asphalt from paved area, finished thickness in inches, and the supplier’s compacted density in pounds per cubic foot.
Find the width to cut both end tiles in a centered row. Set the full tile count, tile size, interior joints, wall span, and perimeter gaps at each end.
Calculate lumber volume in board feet for a stack of identical boards. Enter thickness and width in inches, length in feet, and the board count.
Estimate bricks for one wall face using net wall area, brick dimensions, mortar joint thickness, and waste. Subtract doors and windows from the area first.
Calculate the finished width of one cabinet door from the clear opening and the overlay at each side. Enter different overlaps for an asymmetric layout.
Estimate how many running feet a cartridge can extrude using US fluid ounces and round bead diameter. Tooling losses and uneven joints reduce actual coverage.
Plan a centered mat opening from board and opening dimensions in inches. See the left and right border width and the separate top and bottom border width.
Turn the volume of your pour into a whole-bag count. Use the mixed yield in cubic feet printed on the bag and allow extra for spills or uneven ground.
Estimate the cubic yards of concrete for a slab from length and width in feet and depth in inches. Add an overage percentage to the order.
Calculate fabric width for each curtain panel from rod width, fullness, panel count, and both side hems. Use the fabric consumed by each finished hem.
Count full-length board rows across a rectangular deck using its width, each board’s face width, and the chosen gap. The final row may need trimming.
Estimate whole drywall sheets for walls and ceilings. Use their combined finished area, the panel dimensions, and a cutting allowance.
Find the post count for a straight fence run from its length and maximum spacing. The count includes both end posts and rounds up the number of bays.
Turn a measured inside corner angle into the equal saw setting for two flat trim pieces. The result is degrees from a square crosscut with no bevel.
Convert the floor area into full boxes of flooring using the square feet per box. Set your cutting allowance before the result rounds up.
Find equal edge-to-edge spacing for a row of same-width frames. The calculation uses the available wall width and leaves matching gaps at both outer ends.
Convert cubic yards of gravel into US short tons using the supplier’s bulk density in pounds per cubic yard for your particular aggregate.
Find how many US gallons of paint a job takes using the area after subtracting openings, the number of coats, and the coverage listed on the paint can.
Find the square footage of a sloped roof from its horizontal footprint and rise per 12 inches of run. Include overhangs and group planes with the same pitch.
Count equal-width strips across the usable width of a plywood sheet with a specified blade kerf. Use the width remaining after any initial edge trimming.
Estimate how many US gallons a rectangular pool holds. Use inside length, width, and average water depth in feet to account for a uniformly sloping floor.
Convert roof pitch into degrees above horizontal using rise and run in inches. A rise of 6 inches over a 12-inch run gives an angle of about 26.6°.
Calculate the cubic yards of concrete for identical round footings. Enter the inside diameter in inches, the depth in feet, and how many you plan to fill.
Calculate percent grade from a vertical change and horizontal distance in feet. Enter a negative vertical change to measure a downhill slope.
Divide a floor-to-floor rise into equal stair risers. Enter total rise and the maximum height per step to see the riser count and actual height in inches.
Add the tread runs, vertical risers, and extra finish length to size a stair runner in inches. Enter separate counts for the surfaces the runner covers.
Count rectangular tiles for a wall or floor using surface area, measured tile dimensions, and a waste allowance. The estimate treats grout gaps as zero.
Estimate whole wallpaper rolls from wall and roll dimensions. Allow for top and bottom trimming and a repeating straight-match pattern.