ADC Resolution in Millivolts per Code
Find the ideal millivolts represented by one ADC code. Enter bit depth and the minimum and maximum input voltages for unipolar or bipolar ranges.
Use Ohm’s law, solve a voltage divider or estimate an RC time constant. Find circuit tools for resistors, capacitors, inductors and power.
Try a shorter search or choose another category.
Find the ideal millivolts represented by one ADC code. Enter bit depth and the minimum and maximum input voltages for unipolar or bipolar ranges.
Estimate battery life in hours using rated capacity in mAh, average load in mA, and the share of capacity available before cutoff.
Find the capacitive reactance magnitude in ohms at a selected frequency. Enter capacitance in microfarads and sinusoidal frequency in hertz.
Find charge on a capacitor plate in microcoulombs from capacitance in microfarads and the signed voltage across its terminals.
How much energy does a charged capacitor hold? Enter capacitance in microfarads and voltage in volts to find stored energy in millijoules.
Find capacitor voltage at a given time after a supply change. Set the initial and final voltages, circuit resistance, capacitance, and elapsed milliseconds.
Calculate DC electrical power in watts from terminal voltage and current. The sign shows whether a component absorbs or delivers power.
Estimate secondary RMS voltage from primary RMS voltage and the turns in each winding. The ideal transformer model omits winding loss and voltage drop.
Determine an inductor’s reactance in ohms from inductance in millihenries and frequency in hertz. The ideal inductive reactance falls to zero at DC.
Calculate magnetic energy in millijoules from inductance in millihenries and current in amperes. Assumes the inductance is constant at that current.
Find the signed closed-loop gain of an inverting op-amp stage. Enter input and feedback resistances in kilohms to get the output-to-input voltage ratio.
Find the natural frequency in hertz of an ideal LC circuit. Use inductance in millihenries and capacitance in microfarads to explore component choices.
Find the closed-loop voltage gain of a noninverting op-amp from its feedback and ground-side resistors. Both resistor inputs use kilohms.
Use Ohm’s law to calculate current in amperes through a resistor. Enter the measured voltage drop in volts and the resistance in ohms.
Find total capacitance for two or three capacitors across the same nodes. Enter each value in microfarads and leave an unused branch at zero.
Calculate the equivalent resistance of two resistors connected in parallel. Enter both branch values in ohms, including zero for a shorted branch.
Convert power in milliwatts to dBm, a logarithmic level referenced to one milliwatt. Fractional milliwatt inputs give negative dBm values.
Calculate what percentage of a repeating signal is high. Enter the high pulse width and the full period in milliseconds for one cycle.
Find the −3 dB cutoff frequency of a first-order RC filter from resistance in kilohms and capacitance in nanofarads, assuming negligible loading.
Find the RC time constant in milliseconds using resistance in kilohms and capacitance in microfarads. One time constant covers about 63% of a voltage step.
Estimate how quickly current approaches its final value in a series RL circuit. Enter inductance in millihenries and total resistance in ohms.
Calculate the equivalent capacitance of two capacitors wired in series. Enter both values in microfarads to find the effective capacitance across the pair.
Find the equivalent resistance of two or three resistors in series. Enter each value in ohms and use zero for an unused position.
Calculate the impedance magnitude in ohms of a series RLC circuit at a given frequency, accounting for the opposing inductive and capacitive reactances.
Convert the peak voltage of a zero-offset sine wave to its RMS voltage. For an oscilloscope reading in volts peak-to-peak, enter half that value.
Find the unloaded output voltage across the lower resistor in a two-resistor divider. Enter supply voltage and both resistances in ohms.
Express an amplifier’s voltage gain or attenuation in decibels. Enter like-for-like input and output amplitudes, such as two RMS voltage readings.
Estimate DC wire resistance from conductor length in meters, cross-section in mm², and material resistivity. Include both conductors for a complete loop.